Euro Taper Ties Data Sheet
Euro Taper Ties
15mm and 20mm Euro thread ties for faster gangform assembly and stripping
Euro Taper Ties are used in forming situations where the ties are completely removed after the concrete has cured. Commonly used with European-style gangform systems, Euro Taper Ties enable contractors to efficiently assemble and strip formwork. Applying waterproof grease evenly on each Euro Taper Tie prior to concrete placement facilitates removal.
Euro Taper Ties have flats at the larger end, allowing the tie to be turned with
a wrench during stripping. A hammer is used to strike the tie on the smaller end for removal from the gangform and wall.
The Euro Taper Tie, two Flat Washers and two Wing Nuts provide a removable and reusable gangform tie system.
15mm Euro Taper Ties
Part Number
Description
Taper Dimension
SWL*
SBETT30587815MM
15mm Taper Tie 30” 5/8:7/8
5/8” to 7/8”
18,750 lbs
SBETT38587815MM
15mm Taper Tie 38” 5/8:7/8
5/8” to 7/8”
18,750 lbs
SBETT42587815MM
15mm Taper Tie 42” 5/8:7/8
5/8” to 7/8”
18,750 lbs
SBETT3658115MM
15mm Taper Tie 36” 5/8:1
5/8” to 1”
18,750 lbs
SBETT4258115MM
15mm Taper Tie 42” 5/8:1
5/8” to 1”
18,750 lbs
SBETT4858115MM
15mm Taper Tie 48” 5/8:1
5/8” to 1”
18,750 lbs
SBETT5458115MM
15mm Taper Tie 54” 5/8:1
5/8” to 1”
18,750 lbs
SBETT6058115MM
15mm Taper Tie 60” 5/8:1
5/8” to 1”
18,750 lbs
SBETT6658115MM
15mm Taper Tie 66” 5/8:1
5/8” to 1”
18,750 lbs
* Other sizes available on request.
** Safe working load (tension) at safety factor of 2:1.
840 South 25th Ave Bellwood, IL 60104 708-493-9569 www.surebuilt-usa.com
01/24
Part Number
SBETT4278120MM
SBETT4878120MM
SBETT5478120MM
SBETT6078120MM
SBETT427811420MM
SBETT487811420MM
SBETT547811420MM
SBETT607811420MM
20mm Euro Taper Ties
Description
20mm Taper Tie 42” 7/8:1
20mm Taper Tie 48” 7/8:1
20mm Taper Tie 54” 7/8:1
20mm Taper Tie 60” 7/8:1
20mm Taper Tie 42” 7/8:1-1/4
20mm Taper Tie 48” 7/8:1-1/4
20mm Taper Tie 54” 7/8:1-1/4
20mm Taper Tie 60” 7/8:1-1/4
Taper Dimension
7/8” to 1”
7/8” to 1”
7/8” to 1”
7/8” to 1”
7/8” to 1-1/4”
7/8” to 1-1/4”
7/8” to 1-1/4”
7/8” to 1-1/4”
SWL*
32,500 lbs
32,500 lbs
32,500 lbs
32,500 lbs
32,500 lbs
32,500 lbs
32,500 lbs
32,500 lbs
* Other sizes available on request.
** Safe working load (tension) at safety factor of 2:1.
Part No.
SBWN58
SBWN58P
SBWN58SP
SBWN78
SBWN78P
SBWN78SP
Part No.
SBFW12551116
SBFW12551516
Wing Nuts
Description
15mm Wing Nut
15mm Wing
15mm Wing
Nut Washer
Nut with Swivel Plate
20mm Wing Nut
20mm Wing
20mm Wing
Nut Washer
Nut with Swivel Plate
Flat Washers*
* Other sizes available on request.
Description
Flat Washer 1/2” Plate
Flat Washer 1/2” Plate
Dimensions
5” x 5” with 11/16” Hole
5” x 5” with 15/16” Hole
Installation:
1. Slide the proper size flat washer and thread a wing nut on to the coil thread of the larger side on each Euro Taper Tie.
2. Apply waterproof grease that is not affected by the chemicals in concrete onto the tapered surface of each tie.
3. Align forms and insert a Euro Taper Tie through the waler on the back, then guide it through the face, rebar and opposite gang.
4. Slide a flat washer on the open side of
the Euro Taper Tie and thread a wing nut, adjusting it as needed until the forms are set in position.
5. Once the concrete has been placed and cured, remove the wing nut and flat washer from the smaller end of the Euro Taper Tie.
6. Use a hammer to strike the Euro Taper Tie on the smaller end to remove it from the gangforms and wall.
Taper Tie Thread Dimensions
Large End
15 mm 12”
15 mm 12”
20 mm 12”
20 mm 12”
Small End
15 mm 12”
15 mm 12”
20 mm 12”
20 mm 12”
Thread Diameter
Thread Length
Thread Diameter
Thread Length
