Edge Form Brackets

Edge
Form Brackets
Edge Form Bracket 6×8, 9×11
Reuse instead of cutting lumber blocks for bracing and start forming faster
The one-piece plastic design is a wedge-shape that
braces tilt-up edge forms. The 6×8 Edge Form Bracket
has a 6” side for slabs 6” to 7”, and an 8” side for slabs
8” to 9”. The 9×11 Edge Form Bracket has a 9” side
for slabs 9” to 11”, and a 11” side for slabs 11” to 13”.
Both sides of the Edge Form Bracket have a fl at sur-
face with holes for attachment .
The top of the Edge Form Brackets should always be
positioned below the overall form height so they do
not interfere with concrete screeding or fi nishing.
Edge Form Bracket 9×11
Part No. Description
SBEFX9X11 Edge Form Bracket 9”x11”
SBEFG6X8 Edge Form Bracket 6”x8”
The 9×11 Edge Form Bracket can be nailed, screwed
or glued to lumber and concrete. The brackets can be
stripped, stacked, saved and reused.
Tack It – Edge Form Brackets* have sides with holes
for nail attachment to lumber and concrete. 1/4”x1”
plastic nails are available.
Stick It – Edge Form Brackets have fl at sides for
Spray Adhesive or All Weather Adhesive attachment.
Scrape It – Edge Form Brackets can be removed
from surfaces with a long-handle scraper and
cleaned.
Stack It – Edge Form Brackets “nest” together for
handling and storage.
2
Call 708-493-9569
Construction Adhesive
Position, bond, and remove materials in tilt-up casting beds
Construction Adhesive
A high-strength, fast-drying, low VOC, pressure-
sensitive adhesive used for positioning chamfers,
reveals and rustications in tilt-up casting beds.
Suitable for concrete, metal, plastic and wood
surfaces.
All Weather Adhesive
A one-part, moisture cure that can be used in
both wet and dry conditions to adhere a variety of
substrates. The high strength bond is fl exible and
can provide sealant properties. Its high initial green
strength and non-slump formula is ideal for both
vertical and horizontal applications. Cure time can be
24 hours or more, depending on the environment.
Construction Adhesive Edge Form Bracket Installation
Adhesives
Part No. Description Packaging
SBFCA14 SBFAWA20 SBFCA28 Construction Adhesive – LVOC Inverted Aerosol Spray – 14oz can All-Weather Adhesive – 20 oz sausage – 100% solids Construction Adhesive – Canister Tank Spray – 28 lbs 12/case, 108 cases/pallet
12/case, 45 cases/pallet
36/pallet
All Weather Adhesive – sausage
Construction Adhesive
aerosol can
Construction Adhesive
canister
www.surebuilt-usa.com 3
Adhesive Cleaner & Accessories
Part No. Description Packaging
SBFAC5 Adhesive Cleaner – 5 gallon pail 36/pallet
SBFCGAF Canister Gun w/Adjustable Flow –
SBFCH12 Canister Hose – 12’ Length –
SBCGNB620AL Caulking Gun for 20oz sausage, bulk, cartridge –
Canister Gun with Adjustable Flow Rate Caulking Gun for 20 oz, Sausage, Bulk, Cartridge
Adhesive Cleaner
Adhesive Cleaner was designed to help clean up
adhesive residue.
The solvent system attacks residue and can be
applied with a sponge and applicator.
Adhesive Cleaner is great for removing common
aerosol adhesives used in tilt-up construction.
Bondbreakers that chemically react with the concrete
slab and bondbreakers containing wax will require
physical abrasion to prep an area.
Site test recommended.
4
Call 708-493-9569
Construction Adhesive Guidelines
1. Use a curing chemical or curing process that is compatible with the Construction Adhesive
Use of bondbreakers or curing compounds containing wax will make bonding to the concrete slab more
diffi cult. Chemicals that aid in curing, meet ASTM C 309 on a steel troweled surface, and do not aff ect
adhesion such as SureBuilt SureCure should be considered. Consult with SureBuilt Tilt-Up Engineering for
more information. Site test recommended.
2. Allow suffi cient concrete curing
Allow a minimum of three curing days (seven days preferred) after placing a concrete slab. Check for residual
moisture before applying adhesive to a newly-placed concrete surface.
3. Carefully prepare the surface
Bonding surfaces (concrete, metals, plastics, wood) must be free of oil, dirt, dust and/or other particles. Use a
hard bristle brush/broom to clean the surfaces. When necessary, use an angle grinder with a wire cup brush
or Adhesive Cleaner. Note: use of bondbreaker or any cure with wax will inhibit bonding performance of
Construction Adhesive.
4. Spray adhesive in a consistent pattern
Applicator tip should be approximately 10 inches from the surface. Constantly move the applicator to minimize
overlap and/or over application. Several light spray applications typically provide more consistent and thorough
coverage.
5. Provide adequate fl ash time
Adhesive should be applied to both surfaces, then allowed to “fl ash off ” before matching and bonding those
surfaces. Flash time is approximately 1-3 minutes depending on the ambient temperature and weather
conditions.
6. Let adhesive dry
Adhesive should be dry to the touch on both surfaces before matching and bonding those surfaces. The
adhesive can remain “tacky,” even when it is dry.
7. Apply even pressure to materials
Match treated surfaces and apply heavy, consistent pressure. When bonding longer lengths of materials,
be sure they are positioned straight and fl at. When bonding longer lengths of materials, be sure to allow
approximately 1/16” space for expansion.
8. Check the base
Force from nail guns and/or other power tools can disrupt bonded materials. Allow bonded areas to fully cure
before performing other forming operations. Use instant-bond Sticky Sheets to reattach dislodged materials.
8. Water resistance
For reveals and rustications, use impervious materials like plastics. Check adhesive and plastic compatibility
before beginning any application. Do not attempt to match and bond wet materials. Incidental moisture after
installation is acceptable.
www.surebuilt-usa.com 5
Line Card
Bar Support *
Slab Bolster
Slab Bolster Upper
Individual High Chair
Form Ties *
X-Flat Ties
Base Ties
Aluminum Form Ties
Continuous High Chair
Heavy Forming *
Continuous High Chair Upper
SOLO Clamp Form 1500PSF
Beam Bolster
SureCurve Radius Form
Bridge Deck Forming
Bridge Overhang Bracket *
Curing Blankets
Exterior Hangers *
Exterior Half Hangers *
Interior Hangers *
Interior Half Hanger *
Adjustable Joist Hanger
Sure Beam
Articulated Waler
Steel Circular Column Form
Taper Ties
She-Bolts
Inner Units
Euro Taper Ties
Euro She-Bolts
Flat Washers
Coil Rod *
1/2”, 3/4”, 1” Coil Rod
1-1/4” Coil Rod
15mm, 20mm Coil Rod
Coil Ties *
1/2”, 3/4”, 1” Coil Ties
1-1/4” Coil Ties
Concrete Hoppers
Hoppers
Elephant Trunk
Tremie Pipe
Steel Collar
Floor Systems *
Dowel Basket
Taper Dowel
Steel Edge Nosing
VaporStop & Tape
GFRP Reinforcement Bar *
#2-#11 Reinforcement Bar
Metal Rib *
Expanded Metal Mesh
Modular Braces *
Type 6-5/8”
Type 8-5/8”
Pipe Braces *
Plywood Forming *
Coil Ties
Pencil Rod and Clamps
Self-Centering Ties
Snap Ties
Rebar Safety Caps
Rebar Splicing *
Groutec
Unitec
Self-Riser System *
Shoring *
Cross Braces
Frames
Post Shores
Screw Jacks
Snap Ties *
SPAN-X Beams *
Staybox Rebar Splicing *
Steel Stakes *
3/4” Stakes
7/8” Stakes
Stud Rail DSA & DSAR *
Thermal Break
SurePly™ Handset Forming *
Panels and Fillers
Hardware
HD Loop Ties
X-Flat Ties
Birch Plywood
Form Liners *
HIPS – Single Use
ABS – Up to 10 Uses
PE – Up to 40 – 50 Uses
PPE – Up to 100+ Uses
Form Ties *
HD Loop Ties
HD Gang Loop Ties
Precast
Anchor Rail HD
Coil Inserts *
Column Wall Edge Connector *
Ferrule Inserts *
Helical Ground Anchors *
Ring and Cable Lifters
Slant Anchor *
Straight Leg Anchor *
Wall Base Connector *
Wire / FRP Truss *
Tilt-Up
Brace Inserts *
Helical Ground Anchors *
Lifting Hardware
ProLift Inserts *
Slant Anchor *
SureLift (SL) Inserts *
Edge Form Brackets
Construction Adhesive *
FRP Truss / Connectors *
XL Lift Inserts *
Walers *
Butt Plate
Double Channel
* Products are Made in the USA or available to be made in the USA
2525 Armitage Ave
Melrose Park, IL 60160
708-493-9569
www.surebuilt-usa.com
02/25