Concrete Construction Products

Concrete

Construction

ProductsTable of Contents

Handset Forms ……………………………………………… 3

SurePly Panels and Fillers

Ties and Hardware

Job Built Forming Systems ……………………………….. 4

Coil Ties

Self-Centering Tie and Bracket

Clamp Forms …………………………………………………….. 5

Panels and Components

Ties and Hardware

Heavy Forming ………………………………………………….. 6

Taper Ties and Hardware

She-Bolts and Hardware

Euro Ties and Hardware

Large Gathering Members………………………………….. 7

Butt Plate Waler

Articulated Waler

Sure Beam

Precast ………………………………………………………………8

Tilt-Up ………………………………………………………………..9

Wall Bracing ……………………………………………………. 10

Ground Anchor Systems ………………………………….. 11

Self Rising CoreForm Systems …………………………12

Stud Rail

Thermal Break

Staybox

Formliners & Specialty Forming ………………………..13

American Formliners

Steel Circular Column Forms

Friction Collars

Post Shores & Shoring ……………………………………..14

Post Shores

SPAN-X

Frames and Crossbraces

Bridge Deck & Fiberglass Reinforcement Bar …… 15

Interior, Exterior, & Adj. Hangers

Bridge Overhang Brackets

GFRP Deformed Fiberglass Bar

Rebar Support …………………………………………………. 16

Slab Bolster & Beam Bolster

Individual High Chairs

Plastic Bolster and Chairs

Floor Systems & Load Transfer ………………………… 17

Basket Dowel

Taper Dowel

Steel Edge Nosing

Floor Systems & Load Transfer ………………………… 18

Dowel Sleeves

Paving Dowels & Baskets

Steel Stakes & Misc. ………………………………………… 19

2

SureBuilt Locations

California – (714) 871-9434

130 N. Gilbert St

Fullerton, CA 92833

Florida – (813) 606-5727

9225 Bay Plaza Blvd Ste 407

Tampa, FL 33619

Florida – (813) 606-5727

4000 North Combee Rd

Lakeland, FL 33805

Illinois – (708) 493-9569

2525 Armitage Avenue

Melrose Park, IL 60160

Illinois – (630) 231-6900

1200 N Prince Crossing Rd

West Chicago, IL 60185

Illinois – (877) 533-5842

645 Airport Rd

Centralia, IL 62801

Indiana – (812) 248-9750

305 S New Albany St

Sellersburg, IN 47172

Mississippi – (601) 855-7242

576 Church Rd

Madison, MS 39110

North Carolina – (919) 553-7124

13308 US-70 BUS

Clayton, NC 27520

Pennsylvania – (888) 734-5561

525 E Mifflin St

Lebanon, PA 17046

Tennessee – (423) 942-4090

150 Hickman Rd

Jasper, TN 37347

Texas – (713) 413-4134

301 W. Foxshire Ln

Houston, TX 77053

Call 708-493-9569Handset Forms

SurePly™ Handset

Overview

The #1 USA BUILT CONCRETE FORM

Two 2×8 panels are equal to the contact area of a 4×8

sheet of plywood, yet the SurePly forming system can

be moved, placed, tied, poured and stripped 75%

faster than job-built plywood forms.

From house foundations to power plants and tanks.

Small or large projects, simple or cut-up layouts, and

handset or gangform applications, will benefit from

these SurePly labor-saving features:

•

High-carbon 55,000 PSI structural steel frame

•

Rugged frame with 45% more weld than others

•

Full 2”x2” crossmember support angle every foot

•

Allowable 1,000 psf load-rated system

•

Added dado slots make step footings easy

•

Integral handle for carrying and setting

•

Baked-on powder paint in 12 optional colors

•

Long-lasting 1/2” Birch or optional HDO plywood

•

Panels in heights from 3’ to 10’, width 24”

•

Fillers in heights from 3’ to 10’, widths 1” to 22”

•

Inside corners in heights from 3’ to 10’, 6”x6” size

•

Simple hardware for faster assembly

•

Straight or curved walls

Wedge Bolt

for fast connections

Application Guide

HD Loop Tie

One-Piece Waler Clamp

(used with 2×4 lumber)

for formwork alignment

X-Flat Tie

HD Turnbuckles

(used with 2×4 lumber)

for plumbing forms

Base Tie

www.surebuilt-usa.com 3Job Built Forming Systems

Snap Tie System

Job-built forming with 3/4” plywood, 2×4 lumber, Snap

Ties and Jahn-style Brackets is popular on many

construction sites.

Short-end (SE) Snap Ties are available for single waler

applications. Long-end (LE) Snap Ties are available

for waler/strongback combinations. Odd-end (OE)

Snap Ties are available for forming with a single waler

on one side and waler/strongback combination on the

other side.

https://surebuilt-usa.com/docs/Snap-Ties.pdf

Snap Tie

Waler

Bracket

Jahn-style

Tie Bracket

Coil Ties

The 2-Strut and 4-Strut designs, in standard and

heavy-duty capacities, are designed for job-built

plywood forming. The coil ties are resistance-welded

for reliable performance and safety.

Coil Ties are available with optional cones, waterseals,

galvanized finish or custom specification on request.

Other related products include Coil Rod, Coil Nuts, Coil

Nut Washers, Flat Washers and Coil Bolts.

2-Strut

Coil Tie

4-Strut

Coil tie

2-Strut

ConeFast Coil Tie

4-Strut

ConeFast Coil Tie

TieLock™ System

A self-centering loop tie and TieLock Bracket, with 3/4”

plywood as the form face and 2×4 lumber as the waler,

creates an economical concrete forming system.

The self-centering tie sets the wall dimension, sits flush

up against the plywood face, and breaks back cleanly

within the plastic cone.

Typical tie spacing is 16”x24” for most concrete walls.

The TieLock Bracket hooks the tie loop, while securely

holding the 2×4 lumber walers. A Strongback Bracket

hooks onto the TieLock Bracket when needed.

Self-centering loop tie

w/optional waterseal

TieLock Bracket

Strongback Bracket

4

Call 708-493-9569Clamp Forms

SoloForm™ Forming System

Overview

The strongest handset system on the market is rated

at 1,500 psf, and doubles as a gangform system, with

the addition of larger 4’ x 8’, 6’ x 8’, and 8’ x 8’

panels. Common components minimize inventory

and maximize productivity, no matter the forming

application.

Panels

•

•

•

•

Large: 8’ x 8’, 6’ x 8’, 4’ x 8’

Multipurpose: 36” x 8’, 36” x 6’, 36” x 4’

Standard Panels 8” – 30” wide by 4’, 6’, and 8’

Typical Gang: 8’ x 10’ up to 8’ x 24’

•

Simple Connections

A small, lightweight Wedge Clamp is used to connect

the panel joints. The clamp can be positioned at any

joint with one hand, then secured with a hammer strike.

This simple connection makes assembly and any

reconfi guration quick and efficient.

Lightweight Design

Panels only weigh an average of 8.5 lb / ft, and total

system appx 10.5 lb / ft. making it lightweight, yet

exceptionally durable. The 1,500 psf rating, makes it

the strongest handset system on the market. While

the larger 8’ x 8’ gangform panel weighs 8.75 lbs

per square foot, it only requires four taper ties for a

1,500 psf rating. This lightweight design provides both

modular versatility and strength.

Heavy-Duty Components

Long service life is virtually guaranteed with heavy-

duty components. The side rail and cross members

are rolled from 50 ksi steel. Precision welding turns

individual components into a single structural frame.

Each frame is further reinforced with corner blocks for

durability. The completed frame is then galvanized to

resist corrosion.

American-Made

The entire system is sourced and manufactured in

the United States. From the steel shapes, to rolling

the frame profile, to automated welding, to hot-dip

galvanizing, to birch plywood facing, and a thorough

final inspection, SoloForm is the only concrete forming

system you will ever need.

Application Guide

www.surebuilt-usa.com 5Heavy Forming

Taper Ties and Hardware

Taper Ties are used in forming situations where the

ties are completely removed from the concrete after

the pour has cured. Commonly used with gangform

systems, Taper Ties enable contractors to efficiently

assemble and strip formwork.

Taper Ties are squared-off at each end, allowing the tie

to be turned with a wrench during the removal process.

The tie can also be struck on the squared-off end of

the smaller side with a hammer for removal from the

gangform and wall.

1/2” with 7.5 kip SWL to 1-1/4” with 50 kip SWL

She-Bolts and Inner Rods

She-Bolts are heavy duty, reusable forming ties used

for medium and heavy concrete forming applications.

She-Bolts are used in combination with an Inner Rod or

Coil Rod cut-to-length on the job site.

The expendable Inner Rod joins two She-Bolts to

create the form tie assembly. A Flat Washer and Wing

Nut placed on the threaded end transfers the concrete

load to the walers.

She-Bolt

Inner Rod w/optional waterseal

Inner Rod cut from Coil Rod

Euro Ties and Hardware

Standard 15mm and 20mm threaded ties are

compatible with European-style forming systems and

designed for fast gangforming. Each end of the tie is

threaded to the same diameter so the Wing Nut works

on either end. Taper Ties, She-Bolts and Inner Rods

are available in sizes to meet project specifications.

Euro-style

Taper Tie

Euro-style

Wing Nut

Flat Washers,

any size & thickness

6

Call 708-493-9569Large Gathering Members

Butt Plate Walers

The Butt Plate Waler is one of the most popular waler

designs. Double 6” steel channel has 13/16” holes for

3/4” bolts, spaced on 6” centers for waler attachment

hardware. The channels are positioned back-to-back

and separated by a 3” gusset or spacer sleeve. The

1/2”x9”x9” steel plates have holes for

end connections so different waler

lengths can be combined. Butt Plate

Walers are available in 2’, 3’, 4’, 6’, 8’,

10’ and 12’ lengths.

Note: Pafco- and Symons-style double-channel steel

walers are also available.

Articulated Walers – Circular Wall System

Start with 3/4” plywood, aluminum joists or

wood beams you may already own, connecting

hardware, and the Articulated Waler, then build and

“flex” the gang to any radius from 20’ to 180’.

The adjustment screws make it easy to reconfigure the

forming radius Standard taper ties or she-bolts, with flat

washers and nuts, complete the forming assembly.

Sure Beam

The Sure Beam is a HD infrastructure beam that

complements the advantages of the standard SureBuilt

forming systems. The unique hole pattern makes the

Sure Beam adaptable to most forming and shoring

configurations.

The ability to bolt to all the flanges adds efficiency.

When bolted end-to-end as a continuous beam, the

connection develops the full strength of the resulting

stud.

Commons uses for the Sure Beam include: brace,

waler, strongback, shoring, aligner, truss, and other

forming and shoring applications.

The Pivot Bracket provides the connection between

the Soldier beam brace and forming system when

bolted to the end of the Sure Beam.

www.surebuilt-usa.com 7Precast

Precast

A precast concrete component is formed in a reusable

mold, cured under controlled conditions, transported

to the construction site, and lifted into position. Each

component will require anchors, connectors, inserts

and lifting hardware depending on the application.

Anchor Rail HD

Cast-in-place galvanized channel for positioning and

anchoring mechanical straps and supports.

Bolted Connections

Panel-to-panel, corner, and offset panel bolted

connections Loop, flared, double-flared, criss cross,

L-leg, thin slab and wing types for precast panels.

Coil Inserts

Loop, flared, double-flared, criss cross, L-leg, thin slab

and wing types for precast panels.

Column Connector

Column-to-base connection eliminates the need for

panel bracing and welding.

Ferrule Inserts

Loop, flared, double-flared, criss cross, L-leg, thin slab

and wing types for precast panels.

FRP Truss

Connects concrete wythes for insulated “sandwich”

panels and can be tied to strand.

Groutec

Mechanical splicing system for horizontal and vertical

precast elements

Lifter

Ring-shape design, available in 2.5, 5.0 or 10.0 ton

capacities, rotates through the lifting insert.

Panel Base Connector-P(U.S. Patent No. 11,891,790)

Unique anchor provides simple, grouted, panel-to-

foundation connection without welding or bolting.

Straight Leg Anchor

An insert with anchor loop, steel legs and disposable

plastic former for handling precast panels.

Wall Connector

Bolted wall-to-base and wall-to-wall connection

eliminates the need for panel bracing and welding.

Ferrule Insert

Loop Type

Coil Insert

Criss Cross Type

Anchor Rail

Bolted Connections

Groutec

Panel Base

Connector – P

Uni-Lift Anchor

Column

Connector

DIMENSIONS ARE IN INCHES

MATERIAL:

PART NO:

TITLE: DATE:

UNLESS OTHERWISE SPECIFIED

TOLERANCE:

DECIMAL: ±0.0313

FRACTOR: ±1/32″

ANGULAR: ±1°

UNLESS OTHERWISE SPECIFIED

NOTE: THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE

FINISH: WEIGHT:

DO NOT SCALE DRAWING Sandwich DRAWING NO:

PROPERTY OF SUREBUILT COMPANY. ANY REPRODUCTION IN PART

OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF SUREBUILT

REV: SHEET:

SIZE: 11 X 17

COMPANY IS PROHIBITED.

Panel

DRN. BY:

CKD. BY:

APPR’D. BY:

840 S. 25TH AVE. BELLWOOD, IL 60104

PHONE: (708) 493-9569 – FAX: (708) 493-9601

Erection Anchor

FRP Truss

8

Call 708-493-9569Tilt-Up

Tilt-Up

A tilt-up concrete panel is formed on the construction

site, lifted into position, and braced until the structure is

completed. Each panel requires anchors, connectors,

inserts and lifting hardware depending on the specific

design and application.

Brace Bolt Insert

The safety first, all-in-one, cast-in-place brace insert

includes the coil insert, sleeve, flanged coil bolt and

locator cap ensures 100% match between brace bolt

and brace insert.

Construction Adhesive

Inverted spray cans and canisters of Construction

Adhesive as well as All Weather Adhesive in 100%

solids sausages.

Edge Form Brackets

Reuse instead of cutting lumber blocks for bracing and

start forming faster. Construction Adhesive available.

Lifter

Ring-shaped design, available in 2.5, 5.0 or 10.0 ton

capacities, rotates through the lifting insert.

Panel Base Connector (U.S. Patent No. 11,891,790)

Unique anchor provides simple, immediate, bolted

panel-to-foundation connection without welding.

SureLift (SL) Insert (U.S. Patent Pending)

An effective lifting insert with disposable former and

adjustable plastic feet for height adjustment.

Tilt-Up Profiles

Detailed lines, chamfered edges, and smooth reveals,

for a better tilt-up panel appearance.

8

7

6

5

4

3

2

1

D D

C C

B B

Brace Insert

A A

Lifter

SL Insert

8

7

6

5

4

3

2

1

Edge Form Brackets

Panel Base

Connector

Call SureBuilt for Engineering Services

Tilt-Up Profile

Double Chamfer

Construction Adhesive

www.surebuilt-usa.com 9Wall Bracing

Modular Pipe Braces – NEW PATENT

Modular Pipe Braces

Fewer Braces, more Savings. The Modular Brace

savings are compounded when you consider all

the small, but related steps, in the bracing process.

There are 50% fewer brace inserts, 50% fewer brace

attachments, 50% fewer bolts, 50% fewer man-lifts,

and 50% fewer shipments.

As panels increase in height and weight, you can use

an even longer version of the Modular Brace. With

an 8-5/8” diameter, these components provide the

capacity for the increasing panel sizes.

You can still reconfigure the brace components with

plate-to-plate bolting and always have the size you

need, while reducing inventory.

Modular Pipe Braces have just five basic components

that can be configured into 42’, 52’ or 62’ sizes. These

sizes, with greater capacities, reduce the number of

braces needed for large panels.

The 6-5/8” diameter Modular Braces can be increased

in length with 5’ and 10’ components. The 8-5/8”

diameter Modular Braces can be increased in length

with the 10’ components.

A typical 60’ x 25’ Panel you would need:

6 conventional 5-1/2” dia. braces 42’ compared to

3 Modular Braces (6-5/8” dia.) 42’ or only

2 Modular Braces (8-5/8” dia.) 42’

Pipe Braces

The all-steel pipe braces are available in lengths from

7’-6” to 62’-6” and designed for forming, precast and

tilt-up bracing applications.

Adjustable Pipe Braces have a telescoping pipe for

rough dimension and a 6” threaded connecting shoe

for final adjustment and anchoring. There are three

sizes, ranging from 7’-6” to 40’-0”.

Heavy-Duty Fixed Pipe Braces are large diameter

pipes with greater capacity. There are three sizes of

Heavy-Duty Fixed Pipe Brace, including extensions,

ranging from 31’-0” to 62’-6”.

Call SureBuilt for Engineering Services

10

Call 708-493-9569Ground Anchor Systems

Bracing Accessories

Helical Ground Anchor

A 7’ reusable steel shaft with helix plates that “screws”

into the ground to anchor pipe braces. The HGA has

2 chisel flight finish plates at the bottom and 1 straight

flight finish plate.

Helical Ground Anchor X7 Drivehead

Powerful drivehead for HGA installation.

Helical Ground Anchor Extension

A 4’ reusable steel shaft with 1 straight flight finish

helical plate. The HGA Extension is used when the

needed psi is not reached with the 7’ HGA is installed.

HGA Bracket (U.S. Patent Pending)

Load-rated device for quickly connecting tilt-up pipe

brace shoes to helical ground anchors in 1-Bolt, 2-Bolt,

and 3-Bolt configurations.

Standard Transitional Brace Connector (STBC)

Allows threaded rod at end of brace to be connected to

the HGA or HGA Extension

Pipe Braces attached to

HGA Bracket for Double

Brace Shoe on a Helical

Ground Anchor

HGA X7 Drivehead

HGA Bracket configurations

with and without brace shoe.

Standard Transitional

Brace Connector (STBC)

www.surebuilt-usa.com 11Self Rising CoreForm Systems

Self-Riser

The Self-Riser System is a cost-effective core forming

method, reducing labor, and increasing productivity.

This system allows core formwork to be lifted without a

crane. Simply flipping a few switches moves the entire

assembly, including platforms, plus interior and exterior

formwork, up another story.

The Self-Riser System allows you to construct cores

faster and more efficiently than other conventional core

forming construction methods.

Stud Rail

Stud Rail is a double-headed stud anchor (DSA)

reinforcement system, typically used for concrete deck-

to-column connections to transfer the load further into

the concrete deck, create a larger shear area around

the column, and resist punching shear forces.

Thermal Break

High-density foam with low conductivity concrete

creates a thermal break on concrete balconies. This

combination reduces energy demand by up to 15%

without compromising structural integrity of the balcony.

Staybox

The Staybox system is prebent rebar and a formed

metal box that creates a single “pull out” bar assembly.

The assembly is used as a keyway and lap splice

between concrete construction joints, including slab,

deck, wall, beam and column intersections.

12

Call 708-493-9569Formliners & Specialty Forming

Formliners

100+ patterns and textures are being specified

by architectural / engineering firms and state DOTs.

Single use HIPS, multiple use ABS (up to 10), and high

reuse (40-50 PE, 100+ PPE) formliners available

American Formliners provides several advantages:

•

40+ years of made in USA formliner manufacturing

•

State-of-the-art manufacturing

•

Cost-effective pricing and nationwide availability

•

Custom capability for unique applications

Unitec

Universal shear-bolt coupling system for the

connection of concrete reinforcement bars from ASTM

#4 to #18. The Unitec rebar splicing system can be

assembled onsite using a standard impact wrench

Steel Circular Column Forms

SureBuilt has one of the largest rental fleets in North

America and our primary focus is manufacturing

products that will not only meet but exceed our

customers expectations. Stock rental fleet consists of

180o sections in 1’, 2’, 4’, and 8’ lengths with diameters

from 12” to 96”. Sale only for 8’ long, 54” – 96” diameter.

Friction Collars

CFFE offers rental and sale of Friction Collars. Round

Collars have a rated capacity up to 50,000 lbs per side.

Square / Rectangular have a rated capacity of up to

25,000 lbs per side.

www.surebuilt-usa.com 13Post Shores & Shoring

Post Shores

Post Shores and HD Post Shores can be used for

supporting deck joists or reshoring existing structures.

Post Shore 350: 6’-6” – 11’-5”, SWL 6,445 to 4,400 lbs.

Post Shore 550: 11’ – 18’, SWL 9,367 to 2,732 lbs.

HD Post Shore 350: 7’ – 11’, SWL depending on the

extended length, of up to 10,000 lbs.

HD Post Shore 450: 8’6” to 14’6”, SWL depending on

the extended length, from 8,366 to 10,000 lbs.

Set the Post Shore height with a captured Quick-

Release Pin and threaded collar. Locked pin position

pictured.

SPAN-X Beams

The SPAN-X is an adjustable horizontal beam made

up of an aluminum box and a telescoping I-beam that

provides a wide range of adjustment.

This self-spanning support can be positioned along

the top of a concrete wall, shelf angle or stringer. The

clear span provides a more accessible work space

underneath, reducing conflict between trades.

Shoring

This shoring and deck support system is designed

for an optimum strength-to-weight ratio, with a tested

rating of 10K leg. The system components include

frames, screw jacks, crossbraces, U-heads and

coupling pins. The frame heights are 3’,4’, 5’ and 6’,

and the widths are 2’ and 4’. The system is quickly

assembled and easily reconfigured for a wide range of

shoring and deck support applications.

Tube Mills

Tube Mills produce load-bearing beams that are

assembled as scaffolding, handrails, agricultural gates

& panels and other customer specific items. for making

Square tube in 1”, 1-1/4”, 1-1/2”, and 2”: 16 ga, 14ga,

12ga, and 11ga. Round tube 1” – 2” diameter in 18ga,

16ga, 14ga, 13ga, 12ga, and 11ga.

Square and round HR, HRPO, and Pre-

Galvanized tube.

14

Call 708-493-9569Bridge Forming & Fiberglass Reinforcement Bar

Interior / Exterior Hangers

Interior Hangers are placed on the top of the interior

bay beams and usually have two 90o end clips to

support the suspended formwork between the beams.

There are several types including Type 1, 4, 7, 8, 9, S,

C, Broached, Precast, Adjustable and hook.

Exterior Hangers are used on the fascia beams and

generally have a 45o end to support the overhang and

a 90o end to support the interior. There are several

types including Type 1-A, 2-A, 4-A, 4-AB, 4-APR, 8-A,

9-A, 9-AB, and 9-APR. All Hangers must support the

live load, dead load, forming load and/or finishing load.

Bridge Overhang Brackets

The Bridge Overhang Bracket adjusts to fit both

structural steel and precast concrete beams. The

size and shape of a bracket is adjusted by changing

the vertical and diagonal legs to meet the specific

overhang requirements. Brackets can be preset, then

moved into position to speed forming operations.

The Extension channel for wider overhangs, Guard

Rail Receptacle for 2×4 lumber uprights, and Wall Plate

for wall mounting, are options adding to the versatility

of the Bridge Overhang Bracket.

JR BOB – 27” channel BOB – 54” channel

HD BOB – 72” channel

HDL BOB – 90” channel

SureSaddle BOB – 10kip

SWL – West Coast Style

Maximum Strength Deformed GFRP

Fiberglass Reinforcement Bar

The only integrally ribbed or deformed maximum

strength GFRP fiberglass reinforcement bar. 1/4th the

weight and CO2 footprint compared to steel, while 3

times stronger.

Some benefits include enhanced jobsite safety,

significant savings in transportation and handling

costs, non-corrosive, non-conductive, suited for any

environmental exposure.

Straight Bar & Bent Bar for any size project.

www.surebuilt-usa.com 15Rebar Support

Slab Bolster

Slab Bolster is used to support rebar and mesh at the

proper elevation in concrete slabs. The legs are spaced

5” on-center and spot-welded to resist bending.

When a runner wire is spot-welded to the feet along the

full length it becomes Slab Bolster Upper. This provides

support on soft surfaces or upper rebar levels.

Beam Bolster

Beam Bolster is used to support rebar at the proper

elevation in beam form soffits. Legs are spaced 2-1/2”

on-center and spot-welded to resist bending.

Standard heights from 3/4” to 4”, in 1/4” increments

Plastic Slab Bolster

Plastic slab bolster with end lock for connecting

longer lengths and secure fit.

Available in 3/4”, 1”, 1-1/2”, and 2”

Spacer Wheels

Designed for ease of installation and a secure

connection to reinforcing steel or mesh.

Space Wheels for mesh

Locking Wheels for bar

On-Grade Chairs

Integrated sand plate for support and stability on soft

surfaces.

Square, Castle, and Paving, Slab-On-Grade Chairs

Chairs for Architectural Concrete

Straddle lower level rebar and support upper mats in

tilt-up and precast panels.

Pro Tilt

Chairs

High Chairs Pro Chairs

16

Call 708-493-9569Floor Systems & Load Transfer

Dowel Baskets

Dowel Baskets provide pre-planned joint stability, load

transfer and smooth transition, in a single cost-effective

assembly.

A properly installed Dowel Basket minimizes joint

spalling, eliminates tripping hazards and improves joint

filler appearance.

The Dowel Basket is recommended for joints up to

0.20” wide and is suitable for all types of ground level

concrete floors, slabs or pavements.

(Dowel Basket sleeve U.S. Patent Pending)

Pro Basket

Taper Dowel

The size and shape of the Taper Dowel provides joint

stability, load transfer and smooth transition, without

restraining concrete floor movement.

The plastic sleeve fastens quickly to edge forms before

concrete placement and the steel plate slides into the

sleeve opening in preparation for the adjoining slab.

A properly installed Taper Dowel is recommended for

joints up to 0.20” wide and is suitable for all types of

ground level concrete slabs, such as jointed floors,

flatwork and pavement.

HD Steel Edge Nosing

High-traffic concrete floors and pavements require

precise load transfer, smooth transition and joint

protection. All of these requirements can be satisfied

with the Steel Edge Nosing assembly.

The full-depth 10’-6” assembly includes steel nosing,

dowel plates and channel for a complete joint

installation. The leave-in-place design eliminates

conventional slab edge forming costs.

The steel nosing, with studs tied to the concrete slab

reinforcement, provides joint edge protection and a

smooth transition from one concrete section to another.

www.surebuilt-usa.com 17Floor Systems & Load Transfer

Dowel Sleeve – Construction Joint

Positioning smooth dowels with lumber edge forms

is easy with the plastic Dowel Sleeve and Nailing

Plate. The plate is attached to the form at the required

spacing and the sleeve is pushed onto the plate before

concrete placement.

When the lumber edge forms are removed, a smooth

steel dowel is placed into each sleeve for the adjoining

concrete slab.

840 S. 25TH AVE. BELLWOOD, IL 60104

PHONE: (708) 493-9569 – FAX: (708) 493-9601

NO:

DATE: REVISION: DRAWN BY: CHECKED BY:

NAME:

PART NO.

DOWEL SLEEVE

THIS DRAWING IS THE PROPERTY OF SUREBUILT MANUFACTURING AND IS SUBJECT TO RETURN UPON DEMAND AND IS LOANED UNDER THE EXPRESS CONDITION

THAT IT WILL NOT BE DUPLICATED, REPRODUCED OR ALTERED IN ANY MANNER WITHOUT U.B.P.WRITTEN APPROVAL.

THE DATA AND INFORMATION CONTAINED HEREON ARE PROPRIETARY TO SUREBUILT SUCH DATA SHALL NOT BE DISCLOSED, DUPLICATED, OR USED IN ANY MANNER DETRIMENTAL TO THE INTERESTS OF SUREBUILT

INFORMATION SHOWN ON THIS DRAWING ARE SUGGESTIONS ONLY AND IN NO WAY IMPLIES ANY GUARANTEES. CONTRACTOR MUST VERIFY DIMENSIONS IN THE FIELD.

CHECKED BY:

DRAWN BY: REV: REF:

SCALE: SIZE: DWG NO.

DATE:

NTS

Xiaobo B 12/30/2019

Dowel Sleeve – Expansion Joint

Expansion boards are predrilled to the proper hole size

and spacing to meet specifications. Once the predrilled

boards are in position, the sleeves are quickly snapped

into place. Integrated collar tabs keep each sleeve in

position and perpendicular to the board face.

Normal concrete expansion and contraction takes

place as the smooth steel dowel bar slides inside the

sleeve.

Plastic sleeves accurately position and align

smooth steel dowels in the adjoining concrete

section.

Paving Dowels & Baskets

Rebar fabrication is an extremely important process

that should be done right. We proudly supply, detail,

and fabricate rebar for all our customers with exact

specifications and project details in mind to meet all

your project requirements.

Baskets: Contraction, Expansion, Rebar, and Tapered

Dowel Bars: 1/2” – 2” Cold Saw Cut for Clean Ends

Baskets sized is based on pavement thickness,

lane width, dowel bar size, and spacing

Epoxy Coated Rebar

Rebar fabrication is an extremely important process

that should be done right. We proudly supply, detail,

and fabricate rebar for all our customers with exact

specifications and project details in mind to meet all

your project needs.

CRSI Certified Coater – Rebar Sizes: 20’ – 60’ / #3 – #18

Epoxy Coating Facility with Shear Line Cutter

18

Call 708-493-9569Steel Stakes & Misc.

Steel Stakes

Each steel stake is hot-rolled with a “pencil” point,

allowing it to be easily driven or hammered into clay,

rock, or compacted soil. The holes on the stakes are

drilled in a spiral, meaning a nail hole will always line

up with the form for quick nailing.

Metal Rib

This leave-in-place sheet is typically used to form

footings, bulkheads, grade beams, pile caps and

blindside walls. The expanded metal sheets are easy

to cut, lap, splice, bend and pierce, minimizing related

forming costs.

EcoForm

Durable, engineered, stay-in-place formwork system

that delivers unmatched durability and performance,

featuring robust 9-gauge main wires spaced at

6-inch centers and cross wires at 3-inch centers for

optimal structural integrity. EcoForm Steel meets

the requirements of ASTM 1064-22 and fulfills the

standards needed for “Green Building” applications,

LEED ® Certified projects.

HD Egress Ladders

HD Egress Ladders can be used to escape from the

basement or as an access option for emergency

personnel. IRC code requires ladders in wells deeper

than 44”. Standard HD Egress Ladders are 4’, 5’ and 6’

lengths.

Grates

High-quality Grates keep people and objects from

falling into the Window Well. The Grate is made of

rolled angle iron steel, and welded steel safety bars.

Premium mesh grates are also available to keep leaves

and other debris out of the Window Wells.

www.surebuilt-usa.com 19Bar Support

Slab Bolster

Slab Bolster Upper

Individual High Chair

Continuous High Chair

Continuous High Chair Upper

Beam Bolster

Bridge Deck Forming

Bridge Overhang Bracket

HD Bridge Overhang Bracket

Curing Blankets

Exterior Hangers

Exterior Half Hangers

Interior Hangers

Interior Half Hanger

Adjustable Joist Hanger

Coil Rod

1/2”, 3/4”, 1” Coil Rod

1-1/4” Coil Rod

15mm, 20mm Coil Rod

Coil Ties

1/2”, 3/4”, 1” Coil Ties

1-1/4” Coil Ties

Concrete Hoppers

Hoppers

Elephant Trunk

Tremie Pipe

Steel Collar

Floor Systems

Dowel Basket

Taper Dowel

Steel Edge Nosing

VaporStop & Tape

Form Liners

HIPS – Single Use

ABS – Up to 10 Uses

PE – Up to 40 – 50 Uses

PPE – Up to 100+ Uses

Form Ties

HD Loop Ties

HD Gang Loop Ties

Line Card

Form Ties

X-Flat Ties

Base Ties

Aluminum Form Ties

Heavy Forming

SOLO Clamp Form 1500PSF

Sure Beam

Articulated Waler

Steel Circular Column Form

Taper Ties

She-Bolts

Inner Units

Euro Taper Ties

Euro She-Bolts

Flat Washers

GFRP Reinforcement Bar

#2-#11 Reinforcement Bar

Metal Rib

Expanded Metal Mesh

Modular Braces

Type 6-5/8”

Type 8-5/8”

Pipe Braces

Plywood Forming

Coil Ties

Pencil Rod and Clamps

Self-Centering Ties

Snap Ties

Precast

Anchor Rail HD

Coil Inserts

Column Wall Edge Connector

Ferrule Inserts

Helical Ground Anchors

Ring and Cable Lifters

Slant Anchor

Straight Leg Anchor

Wall Base Connector

Wire / FRP Truss

Rebar Safety Caps

Rebar Splicing

Groutec

Unitec

Self-Riser System

Shoring

Cross Braces

Frames

Post Shores

Screw Jacks

Snap Ties

SPAN-X Beams

Staybox Rebar Splicing

Steel Stakes

3/4” Stakes

7/8” Stakes

Stud Rail DSA & DSAR

Stud Rail

Thermal Break

SurePly™ Handset Forming

Panels and Fillers

Hardware

HD Loop Ties

X-Flat Ties

Birch Plywood

Renovation

Tilt-Up

Brace Inserts

Helical Ground Anchors

Lifting Hardware

ProLift Inserts

Slant Anchor

SureLift (SL) Inserts

Edge Form Brackets

Construction Adhesive

FRP Truss / Connectors

XL Lift Inserts

Walers

Butt Plate

Double Channel

American Made Products You Can Count On – From One of 9 Surebuilt U.S.A. Factories – Call Right Now!

2525 Armitage Ave

Melrose Park, IL 60160

708-493-9569

www.surebuilt-usa.com

02/26