Concrete Construction Products

Concrete
Construction
Products
Table of Contents
Handset Forms ……………………………………………… 3
SurePly Panels and Fillers
Ties and Hardware
Job Built Forming Systems ……………………………….. 4
Coil Ties
Self-Centering Tie and Bracket
Clamp Forms …………………………………………………….. 5
Panels and Components
Ties and Hardware
Heavy Forming ………………………………………………….. 6
Taper Ties and Hardware
She-Bolts and Hardware
Euro Ties and Hardware
Large Gathering Members………………………………….. 7
Butt Plate Waler
Articulated Waler
Sure Beam
Precast ………………………………………………………………8
Tilt-Up ………………………………………………………………..9
Wall Bracing ……………………………………………………. 10
Ground Anchor Systems ………………………………….. 11
Self Rising CoreForm Systems …………………………12
Stud Rail
Thermal Break
Staybox
Formliners & Specialty Forming ………………………..13
American Formliners
Steel Circular Column Forms
Friction Collars
Post Shores & Shoring ……………………………………..14
Post Shores
SPAN-X
Frames and Crossbraces
Bridge Deck & Fiberglass Reinforcement Bar …… 15
Interior, Exterior, & Adj. Hangers
Bridge Overhang Brackets
GFRP Deformed Fiberglass Bar
Rebar Support …………………………………………………. 16
Slab Bolster & Beam Bolster
Individual High Chairs
Plastic Bolster and Chairs
Floor Systems & Load Transfer ………………………… 17
Basket Dowel
Taper Dowel
Steel Edge Nosing
Floor Systems & Load Transfer ………………………… 18
Dowel Sleeves
Paving Dowels & Baskets
Steel Stakes & Misc. ………………………………………… 19
2
SureBuilt Locations
California – (714) 871-9434
130 N. Gilbert St
Fullerton, CA 92833
Florida – (813) 606-5727
9225 Bay Plaza Blvd Ste 407
Tampa, FL 33619
Florida – (813) 606-5727
4000 North Combee Rd
Lakeland, FL 33805
Illinois – (708) 493-9569
2525 Armitage Avenue
Melrose Park, IL 60160
Illinois – (630) 231-6900
1200 N Prince Crossing Rd
West Chicago, IL 60185
Illinois – (877) 533-5842
645 Airport Rd
Centralia, IL 62801
Indiana – (812) 248-9750
305 S New Albany St
Sellersburg, IN 47172
Mississippi – (601) 855-7242
576 Church Rd
Madison, MS 39110
North Carolina – (919) 553-7124
13308 US-70 BUS
Clayton, NC 27520
Pennsylvania – (888) 734-5561
525 E Miffl in St
Lebanon, PA 17046
Tennessee – (423) 942-4090
150 Hickman Rd
Jasper, TN 37347
Texas – (713) 413-4134
301 W. Foxshire Ln
Houston, TX 77053
Call 708-493-9569
Handset Forms
SurePly™ Handset
Overview
The #1 USA BUILT CONCRETE FORM
Two 2×8 panels are equal to the contact area of a 4×8
sheet of plywood, yet the SurePly forming system can
be moved, placed, tied, poured and stripped 75%
faster than job-built plywood forms.
From house foundations to power plants and tanks.
Small or large projects, simple or cut-up layouts, and
handset or gangform applications, will benefit from
these SurePly labor-saving features:
• High-carbon 55,000 PSI structural steel frame
• Rugged frame with 45% more weld than others
• Full 2”x2” crossmember support angle every foot
• Allowable 1,000 psf load-rated system
• Added dado slots make step footings easy
• Integral handle for carrying and setting
• Baked-on powder paint in 12 optional colors
• Long-lasting 1/2” Birch or optional HDO plywood
• Panels in heights from 3’ to 10’, width 24”
• Fillers in heights from 3’ to 10’, widths 1” to 22”
• Inside corners in heights from 3’ to 10’, 6”x6” size
• Simple hardware for faster assembly
• Straight or curved walls
Wedge Bolt
for fast connections
Application Guide
HD Loop Tie
One-Piece Waler Clamp
(used with 2×4 lumber)
for formwork alignment
X-Flat Tie
HD Turnbuckles
(used with 2×4 lumber)
for plumbing forms
Base Tie
www.surebuilt-usa.com 3
Job Built Forming Systems
Snap Tie System
Job-built forming with 3/4” plywood, 2×4 lumber, Snap
Ties and Jahn-style Brackets is popular on many
construction sites.
Short-end (SE) Snap Ties are available for single waler
applications. Long-end (LE) Snap Ties are available
for waler/strongback combinations. Odd-end (OE)
Snap Ties are available for forming with a single waler
on one side and waler/strongback combination on the
other side.
https://surebuilt-usa.com/docs/Snap-Ties.pdf
Snap Tie
Jahn-style
Tie Bracket
Waler
Bracket
Coil Ties
The 2-Strut and 4-Strut designs, in standard and
heavy-duty capacities, are designed for job-built
plywood forming. The coil ties are resistance-welded
for reliable performance and safety.
Coil Ties are available with optional cones, waterseals,
galvanized fi nish or custom specifi cation on request.
Other related products include Coil Rod, Coil Nuts, Coil
Nut Washers, Flat Washers and Coil Bolts.
2-Strut
Coil Tie
4-Strut
Coil tie
2-Strut
ConeFast Coil Tie
4-Strut
ConeFast Coil Tie
TieLock™ System
A self-centering loop tie and TieLock Bracket, with 3/4”
plywood as the form face and 2×4 lumber as the waler,
creates an economical concrete forming system.
The self-centering tie sets the wall dimension, sits fl ush
up against the plywood face, and breaks back cleanly
within the plastic cone.
Typical tie spacing is 16”x24” for most concrete walls.
The TieLock Bracket hooks the tie loop, while securely
holding the 2×4 lumber walers. A Strongback Bracket
hooks onto the TieLock Bracket when needed.
Self-centering loop tie
w/optional waterseal
TieLock Bracket
Strongback Bracket
4
Call 708-493-9569
Clamp Forms
SoloForm™ Forming System
Overview
The strongest handset system on the market is rated
at 1,500 psf, and doubles as a gangform system, with
the addition of larger 4’ x 8’, 6’ x 8’, and 8’ x 8’
panels. Common components minimize inventory
and maximize productivity, no matter the forming
application.
Panels
• Large: 8’ x 8’, 6’ x 8’, 4’ x 8’
• Multipurpose: 36” x 8’, 36” x 6’, 36” x 4’
• Standard Panels 8” – 30” wide by 4’, 6’, and 8’
• Typical Gang: 8’ x 10’ up to 8’ x 24’
•
Simple Connections
A small, lightweight Wedge Clamp is used to connect
the panel joints. The clamp can be positioned at any
joint with one hand, then secured with a hammer strike.
This simple connection makes assembly and any
reconfi guration quick and efficient.
Lightweight Design
Panels only weigh an average of 8.5 lb / ft, and total
system appx 10.5 lb / ft. making it lightweight, yet
exceptionally durable. The 1,500 psf rating, makes it
the strongest handset system on the market. While
the larger 8’ x 8’ gangform panel weighs 8.75 lbs
per square foot, it only requires four taper ties for a
1,500 psf rating. This lightweight design provides both
modular versatility and strength.
Heavy-Duty Components
Long service life is virtually guaranteed with heavy-
duty components. The side rail and cross members
are rolled from 50 ksi steel. Precision welding turns
individual components into a single structural frame.
Each frame is further reinforced with corner blocks for
durability. The completed frame is then galvanized to
resist corrosion.
American-Made
The entire system is sourced and manufactured in
the United States. From the steel shapes, to rolling
the frame profile, to automated welding, to hot-dip
galvanizing, to birch plywood facing, and a thorough
final inspection, SoloForm is the only concrete forming
system you will ever need.
Application Guide
www.surebuilt-usa.com 5
Heavy Forming
Taper Ties and Hardware
Taper Ties are used in forming situations where the
ties are completely removed from the concrete after
the pour has cured. Commonly used with gangform
systems, Taper Ties enable contractors to effi ciently
assemble and strip formwork.
Taper Ties are squared-off at each end, allowing the tie
to be turned with a wrench during the removal process.
The tie can also be struck on the squared-off end of
the smaller side with a hammer for removal from the
gangform and wall.
1/2” with 7.5 kip SWL to 1-1/4” with 50 kip SWL
She-Bolts and Inner Rods
She-Bolts are heavy duty, reusable forming ties used
for medium and heavy concrete forming applications.
She-Bolts are used in combination with an Inner Rod or
Coil Rod cut-to-length on the job site.
The expendable Inner Rod joins two She-Bolts to
create the form tie assembly. A Flat Washer and Wing
Nut placed on the threaded end transfers the concrete
load to the walers.
She-Bolt
Inner Rod w/optional waterseal
Inner Rod cut from Coil Rod
Euro Ties and Hardware
Standard 15mm and 20mm threaded ties are
compatible with European-style forming systems and
designed for fast gangforming. Each end of the tie is
threaded to the same diameter so the Wing Nut works
on either end. Taper Ties, She-Bolts and Inner Rods
are available in sizes to meet project specifi cations.
Euro-style
Taper Tie
Euro-style
Wing Nut
Flat Washers,
any size & thickness
6
Call 708-493-9569
Large Gathering Members
Butt Plate Walers
The Butt Plate Waler is one of the most popular waler
designs. Double 6” steel channel has 13/16” holes for
3/4” bolts, spaced on 6” centers for waler attachment
hardware. The channels are positioned back-to-back
and separated by a 3” gusset or spacer sleeve. The
1/2”x9”x9” steel plates have holes for
end connections so diff erent waler
lengths can be combined. Butt Plate
Walers are available in 2’, 3’, 4’, 6’, 8’,
10’ and 12’ lengths.
Note: Pafco- and Symons-style double-channel steel
walers are also available.
Articulated Walers – Circular Wall System
Start with 3/4” plywood, aluminum joists or
wood beams you may already own, connecting
hardware, and the Articulated Waler, then build and
“fl ex” the gang to any radius from 20’ to 180’.
The adjustment screws make it easy to reconfi gure the
forming radius Standard taper ties or she-bolts, with fl at
washers and nuts, complete the forming assembly.
Sure Beam
The Sure Beam is a HD infrastructure beam that
complements the advantages of the standard SureBuilt
forming systems. The unique hole pattern makes the
Sure Beam adaptable to most forming and shoring
confi gurations.
The ability to bolt to all the fl anges adds effi ciency.
When bolted end-to-end as a continuous beam, the
connection develops the full strength of the resulting
stud.
Commons uses for the Sure Beam include: brace,
waler, strongback, shoring, aligner, truss, and other
forming and shoring applications.
The Pivot Bracket provides the connection between
the Soldier beam brace and forming system when
bolted to the end of the Sure Beam.
www.surebuilt-usa.com 7
Precast
Precast
A precast concrete component is formed in a reusable
mold, cured under controlled conditions, transported
to the construction site, and lifted into position. Each
component will require anchors, connectors, inserts
and lifting hardware depending on the application.
Anchor Rail HD
Cast-in-place galvanized channel for positioning and
anchoring mechanical straps and supports.
Coil Inserts
Loop, fl ared, double-fl ared, criss cross, L-leg, thin slab
and wing types for precast panels.
Column Connector
Column-to-base connection eliminates the need for
panel bracing and welding.
Edge Connector
A rebar-winged embed tied to reinforcing steel with
“fl at” positioned at the panel edge for later welding.
Ferrule Inserts
Loop, fl ared, double-fl ared, criss cross, L-leg, thin slab
and wing types for precast panels.
Groutec
Mechanical splicing system for horizontal and vertical
precast elements
Lifter
Ring-shape design, available in 2.5, 5.0 or 10.0 ton
capacities, rotates through the lifting insert.
Slant Anchor (U.S. Patent Pending)
Unique anchor provides simple, grouted, panel-to-
foundation connection without welding or bolting.
Straight Leg Anchor
An insert with anchor loop, steel legs and disposable
plastic former for handling precast panels.
Wall Connector
Bolted wall-to-base and wall-to-wall connection
eliminates the need for panel bracing and welding.
Wire / FRP Truss
GFRP or steel truss joins a bottom layer of concrete, a
middle layer of insulation, and a top layer of concrete
into one unit.
Ferrule Insert
Loop Type
Coil Insert
Criss Cross Type
Anchor Rail
Uni-Lift Anchor
Edge Connector
Groutec
Erection Anchor
Slant Anchor
Column
Connector
Wire Truss FRP Truss
8
Call 708-493-9569
Tilt-Up
Tilt-Up
A tilt-up concrete panel is formed on the construction
site, lifted into position, and braced until the structure is
completed. Each panel requires anchors, connectors,
inserts and lifting hardware depending on the specifi c
design and application.
Brace Insert
Standard panel insert with non-rusting plastic feet and
locator plug for subsequent brace attachment.
Construction Adhesive
Inverted spray cans and canisters of Construction
Adhesive as well as All Weather Adhesive in 100%
solids sausages.
Edge Form Brackets
Reuse instead of cutting lumber blocks for bracing and
start forming faster. Construction Adhesive available.
Lifter
Ring-shaped design, available in 2.5, 5.0 or 10.0 ton
capacities, rotates through the lifting insert.
Panel Base Connector (U.S. Patent No. 11,891,790)
Unique anchor provides simple, immediate, bolted
panel-to-foundation connection without welding.
SureLift (SL) Insert (U.S. Patent Pending)
An eff ective lifting insert with disposable former and
adjustable plastic feet for height adjustment.
Tilt-Up Profi les
Detailed lines, chamfered edges, and smooth reveals,
for a better tilt-up panel appearance.
XL Insert
An eff ective lifting insert with disposable former
Brace Insert
Lifter
SL Insert
Edge Form Brackets
Panel Base
Connector
XL Lift Insert
Call SureBuilt for Engineering Services
Tilt-Up Profi le
Double Chamfer
Construction Adhesive
www.surebuilt-usa.com 9
Wall Bracing
Modular Pipe Braces – NEW PATENT
Modular Pipe Braces
Fewer Braces, more Savings. The Modular Brace
savings are compounded when you consider all
the small, but related steps, in the bracing process.
There are 50% fewer brace inserts, 50% fewer brace
attachments, 50% fewer bolts, 50% fewer man-lifts,
and 50% fewer shipments.
As panels increase in height and weight, you can use
an even longer version of the Modular Brace. With
an 8-5/8” diameter, these components provide the
capacity for the increasing panel sizes.
You can still reconfi gure the brace components with
plate-to-plate bolting and always have the size you
need, while reducing inventory.
Modular Pipe Braces have just fi ve basic components
that can be confi gured into 42’, 52’ or 62’ sizes. These
sizes, with greater capacities, reduce the number of
braces needed for large panels.
The 6-5/8” diameter Modular Braces can be increased
in length with 5’ and 10’ components. The 8-5/8”
diameter Modular Braces can be increased in length
with the 10’ components.
A typical 60’ x 25’ Panel you would need:
6 conventional 5-1/2” dia. braces 42’ compared to
3 Modular Braces (6-5/8” dia.) 42’ or only
2 Modular Braces (8-5/8” dia.) 42’
Pipe Braces
The all-steel pipe braces are available in lengths from
7’-6” to 62’-6” and designed for forming, precast and
tilt-up bracing applications.
Adjustable Pipe Braces have a telescoping pipe for
rough dimension and a 6” threaded connecting shoe
for fi nal adjustment and anchoring. There are three
sizes, ranging from 7’-6” to 40’-0”.
Heavy-Duty Fixed Pipe Braces are large diameter
pipes with greater capacity. There are three sizes of
Heavy-Duty Fixed Pipe Brace, including extensions,
ranging from 31’-0” to 62’-6”.
Call SureBuilt for Engineering Services
10
Call 708-493-9569
Ground Anchor Systems
Bracing Accessories
Helical Ground Anchor
A 7’ reusable steel shaft with helix plates that “screws”
into the ground to anchor pipe braces. The HGA has
2 chisel fl ight fi nish plates at the bottom and 1 straight
fl ight fi nish plate.
Helical Ground Anchor Extension
A 4’ reusable steel shaft with 1 straight fl ight fi nish
helical plate. The HGA Extension is used when the
needed psi is not reached with the 7’ HGA is installed.
HGA Bracket (U.S. Patent Pending)
Load-rated device for quickly connecting tilt-up pipe
brace shoes to helical ground anchors in 1-Bolt, 2-Bolt,
and 3-Bolt confi gurations.
Standard Transitional Brace Connector (STBC)
Allows threaded rod at end of brace to be connected to
the HGA or HGA Extension
Pipe Braces attached to
HGA Bracket for Double
Brace Shoe on a Helical
Ground Anchor
HGA Bracket confi gurations
with and without brace shoe.
Standard Transitional
Brace Connector (STBC)
www.surebuilt-usa.com 11
Self Rising CoreForm Systems
Self-Riser
The Self-Riser System is a cost-eff ective core forming
method, reducing labor, and increasing productivity.
This system allows core formwork to be lifted without a
crane. Simply fl ipping a few switches moves the entire
assembly, including platforms, plus interior and exterior
formwork, up another story.
The Self-Riser System allows you to construct cores
faster and more effi ciently than other conventional core
forming construction methods.
Stud Rail
Stud Rail is a double-headed stud anchor (DSA)
reinforcement system, typically used for concrete deck-
to-column connections to transfer the load further into
the concrete deck, create a larger shear area around
the column, and resist punching shear forces.
Thermal Break
High-density foam with low conductivity concrete
creates a thermal break on concrete balconies. This
combination reduces energy demand by up to 15%
without compromising structural integrity of the balcony.
Staybox
The Staybox system is prebent rebar and a formed
metal box that creates a single “pull out” bar assembly.
The assembly is used as a keyway and lap splice
between concrete construction joints, including slab,
deck, wall, beam and column intersections.
12
Call 708-493-9569
Formliners & Specialty Forming
Formliners
100+ patterns and textures are being specifi ed
by architectural / engineering fi rms and state DOTs.
Single use HIPS, multiple use ABS (up to 10), and high
reuse (40-50 PE, 100+ PPE) formliners available
American Formliners provides several advantages:
• 40+ years of made in USA formliner manufacturing
• State-of-the-art manufacturing
• Cost-eff ective pricing and nationwide availability
• Custom capability for unique applications
Unitec
Universal shear-bolt coupling system for the
connection of concrete reinforcement bars from ASTM
#4 to #18. The Unitec rebar splicing system can be
assembled onsite using a standard impact wrench
Steel Circular Column Forms
SureBuilt has one of the largest rental fl eets in North
America and our primary focus is manufacturing
products that will not only meet but exceed our
customers expectations. Stock rental fl eet consists of
180o sections in 1’, 2’, 4’, and 8’ lengths with diameters
from 12” to 96”. Sale only for 8’ long, 54” – 96” diameter.
Friction Collars
CFFE off ers rental and sale of Friction Collars. Round
Collars have a rated capacity up to 50,000 lbs per side.
Square / Rectangular have a rated capacity of up to
25,000 lbs per side.
www.surebuilt-usa.com 13
Post Shores & Shoring
Post Shores
Post Shores and HD Post Shores can be used for
supporting deck joists or reshoring existing structures.
Post Shore 350: 6’-6” – 11’-5”, SWL 6,445 to 4,400 lbs.
Post Shore 550: 11’ – 18’, SWL 9,367 to 2,732 lbs.
HD Post Shore 350: 7’ – 11’, SWL depending on the
extended length, of up to 10,000 lbs.
HD Post Shore 450: 8’6” to 14’6”, SWL depending on
the extended length, from 8,366 to 10,000 lbs.
Set the Post Shore height with a captured Quick-
Release Pin and threaded collar. Locked pin position
pictured.
SPAN-X Beams
The SPAN-X is an adjustable horizontal beam made
up of an aluminum box and a telescoping I-beam that
provides a wide range of adjustment.
This self-spanning support can be positioned along
the top of a concrete wall, shelf angle or stringer. The
clear span provides a more accessible work space
underneath, reducing confl ict between trades.
Shoring
This shoring and deck support system is designed
for an optimum strength-to-weight ratio, with a tested
rating of 10K leg. The system components include
frames, screw jacks, crossbraces, U-heads and
coupling pins. The frame heights are 3’,4’, 5’ and 6’,
and the widths are 2’ and 4’. The system is quickly
assembled and easily reconfi gured for a wide range of
shoring and deck support applications.
Tube Mills
Tube Mills produce load-bearing beams that are
assembled as scaff olding, handrails, agricultural gates
& panels and other customer specifi c items. for making
Square tube in 1”, 1-1/4”, 1-1/2”, and 2”: 16 ga, 14ga,
12ga, and 11ga. Round tube 1” – 2” diameter in 18ga,
16ga, 14ga, 13ga, 12ga, and 11ga.
Square and round HR, HRPO, and Pre-
Galvanized tube.
14
Call 708-493-9569
Bridge Forming & Fiberglass Reinforcement Bar
Interior / Exterior Hangers
Interior Hangers are placed on the top of the interior
bay beams and usually have two 90o end clips to
support the suspended formwork between the beams.
There are several types including Type 1, 4, 7, 8, 9, S,
C, Broached, Precast, Adjustable and hook.
Exterior Hangers are used on the fascia beams and
generally have a 45o end to support the overhang and
a 90o end to support the interior. There are several
types including Type 1-A, 2-A, 4-A, 4-AB, 4-APR, 8-A,
9-A, 9-AB, and 9-APR. All Hangers must support the
live load, dead load, forming load and/or fi nishing load.
Bridge Overhang Brackets
The Bridge Overhang Bracket adjusts to fi t both
structural steel and precast concrete beams. The
size and shape of a bracket is adjusted by changing
the vertical and diagonal legs to meet the specifi c
overhang requirements. Brackets can be preset, then
moved into position to speed forming operations.
The Extension channel for wider overhangs, Guard
Rail Receptacle for 2×4 lumber uprights, and Wall Plate
for wall mounting, are options adding to the versatility
of the Bridge Overhang Bracket.
JR BOB – 27” channel BOB – 54” channel
HDBOB – 72” channel
HDL BOB – 90” channel
Maximum Strength Deformed GFRP
Fiberglass Reinforcement Bar
The only integrally ribbed or deformed maximum
strength GFRP fi berglass reinforcement bar. 1/4th the
weight and CO2 footprint compared to steel, while 3
times stronger.
Some benefi ts include enhanced jobsite safety,
signifi cant savings in transportation and handling
costs, non-corrosive, non-conductive, suited for any
environmental exposure.
Straight Bar & Bent Bar for any size project.
www.surebuilt-usa.com 15
Rebar Support
Slab Bolster
Slab Bolster is used to support rebar and mesh at the
proper elevation in concrete slabs. The legs are spaced
5” on-center and spot-welded to resist bending.
When a runner wire is spot-welded to the feet along the
full length it becomes Slab Bolster Upper. This provides
support on soft surfaces or upper rebar levels.
Beam Bolster
Beam Bolster is used to support rebar at the proper
elevation in beam form soffi ts. Legs are spaced 2-1/2”
on-center and spot-welded to resist bending.
Standard heights from 3/4” to 4”, in 1/4” increments
Plastic Slab Bolster
Plastic slab bolster with end lock for connecting
longer lengths and secure fi t.
Available in 3/4”, 1”, 1-1/2”, and 2”
High Chairs
Individual High Chairs are used to span and straddle
lower rebar, while “cradling” upper level rebar at the
proper elevation. The legs are spot-welded to resist
bending under rebar load.
Plain Plastic-dipped Plastic-tipped
Slab-On-Grade Chair
Integrated sand plate for support and stability on soft
surfaces.
Slab-On-Grade Chair
Uni Chair with Ring
Straddle lower level rebar and support upper mats in
tilt-up panels.
Uni Chair
16
Call 708-493-9569
Floor Systems & Load Transfer
Basket Dowel
The Dowel Basket provides pre-planned joint stability,
load transfer and smooth transition, in a single cost-
eff ective assembly.
A properly installed Dowel Basket minimizes joint
spalling, eliminates tripping hazards and improves joint
fi ller appearance.
The Dowel Basket is recommended for joints up to
0.20” wide and is suitable for all types of ground level
concrete fl oors, slabs or pavements.
(Dowel Basket sleeve U.S. Patent Pending)
Taper Dowel
The size and shape of the Taper Dowel provides joint
stability, load transfer and smooth transition, without
restraining concrete fl oor movement.
The plastic sleeve fastens quickly to edge forms before
concrete placement and the steel plate slides into the
sleeve opening in preparation for the adjoining slab.
A properly installed Taper Dowel is recommended for
joints up to 0.20” wide and is suitable for all types of
ground level concrete slabs, such as jointed fl oors,
fl atwork and pavement.
HD Steel Edge Nosing
High-traffi c concrete fl oors and pavements require
precise load transfer, smooth transition and joint
protection. All of these requirements can be satisfi ed
with the Steel Edge Nosing assembly.
The full-depth 10’-6” assembly includes steel nosing,
dowel plates and channel for a complete joint
installation. The leave-in-place design eliminates
conventional slab edge forming costs.
The steel nosing, with studs tied to the concrete slab
reinforcement, provides joint edge protection and a
smooth transition from one concrete section to another.
www.surebuilt-usa.com 17
Floor Systems & Load Transfer
Dowel Sleeve – Construction Joint
Positioning smooth dowels with lumber edge forms
is easy with the plastic Dowel Sleeve and Nailing
Plate. The plate is attached to the form at the required
spacing and the sleeve is pushed onto the plate before
concrete placement.
When the lumber edge forms are removed, a smooth
steel dowel is placed into each sleeve for the adjoining
concrete slab.
Dowel Sleeve – Expansion Joint
Expansion boards are predrilled to the proper hole size
and spacing to meet specifi cations. Once the predrilled
boards are in position, the sleeves are quickly snapped
into place. Integrated collar tabs keep each sleeve in
position and perpendicular to the board face.
Normal concrete expansion and contraction takes
place as the smooth steel dowel bar slides inside the
sleeve.
Plastic sleeves accurately position and align
smooth steel dowels in the adjoining concrete
section.
Paving Dowels & Baskets
Rebar fabrication is an extremely important process
that should be done right. We proudly supply, detail,
and fabricate rebar for all our customers with exact
specifi cations and project details in mind to meet all
your project requirements.
Baskets: Contraction, Expansion, Rebar, and Tapered
Dowel Bars: 1/2” – 2” Cold Saw Cut for Clean Ends
Baskets sized is based on pavement thickness,
lane width, dowel bar size, and spacing
Epoxy Coated Rebar
Rebar fabrication is an extremely important process
that should be done right. We proudly supply, detail,
and fabricate rebar for all our customers with exact
specifi cations and project details in mind to meet all
your project needs.
CRSI Certifi ed Coater – Rebar Sizes: 20’ – 60’ / #3 – #18
Epoxy Coating Facility with Shear Line Cutter
18
Call 708-493-9569
Steel Stakes & Misc.
Steel Stakes
Each steel stake is hot-rolled with a “pencil” point,
allowing it to be easily driven or hammered into clay,
rock, or compacted soil. The holes on the stakes are
drilled in a spiral, meaning a nail hole will always line
up with the form for quick nailing.
Metal Rib
This leave-in-place sheet is typically used to form
footings, bulkheads, grade beams, pile caps and
blindside walls. The expanded metal sheets are easy
to cut, lap, splice, bend and pierce, minimizing related
forming costs.
Rebar Safety Cap
The patented design (U.S. Patent No. 8,776,464 B2)
is a proven way to prevent injury on work sites and
meets the OSHA 1926.70(b) requirement. Each Rebar
Safety Cap is internally reinforced with a steel plate,
providing additional protection against falls that occur
from an angle. The Rebar Safety Cap fi ts rebar sizes
#3 through #8, or 3/8” to 1” in bar diameter.
HD Egress Ladders
HD Egress Ladders can be used to escape from the
basement or as an access option for emergency
personnel. IRC code requires ladders in wells deeper
than 44”. Standard HD Egress Ladders are 4’, 5’ and 6’
lengths.
Grates
High-quality Grates keep people and objects from
falling into the Window Well. The Grate is made of
rolled angle iron steel, and welded steel safety bars.
Premium mesh grates are also available to keep leaves
and other debris out of the Window Wells.
www.surebuilt-usa.com 19
Bar Support *
Slab Bolster
Slab Bolster Upper
Individual High Chair
Continuous High Chair
Continuous High Chair Upper
Beam Bolster
Bridge Deck Forming
Bridge Overhang Bracket *
Curing Blankets
Exterior Hangers *
Exterior Half Hangers *
Interior Hangers *
Interior Half Hanger *
Adjustable Joist Hanger
Coil Rod *
1/2” Coil Rod
3/4” Coil Rod
1” Coil Rod
1-1/4” Coil Rod
15mm Coil Rod
20mm Coil Rod
Coil Ties *
1/2” Coil Ties
3/4” Coil Ties
1” Coil Ties
1-1/4” Coil Ties
Concrete Hoppers
Hoppers
Elephant Trunk
Tremie Pipe
Steel Collar
Floor Systems *
Dowel Basket
Taper Dowel
Steel Edge Nosing
VaporStop & Tape
Form Liners *
HIPS – Single Use
ABS – Up to 10 Uses
PE – Up to 40 – 50 Uses
PPE – Up to 100+ Uses
Line Card
Form Ties *
HD Loop Ties
HD Gang Loop Ties
X-Flat Ties
Base Ties
Aluminum Form Ties
Heavy Forming *
SOLO Clamp Form 1500PSF
SureCurve Radius Form
Sure Beam
Articulated Waler
Steel Circular Column Form
Taper Ties
She-Bolts
Inner Units
Euro Taper Ties
Euro She-Bolts
Flat Washers
GFRP Reinforcement Bar *
#2-#11 Reinforcement Bar
Metal Rib *
Expanded Metal Mesh
Modular Braces *
Type 6-5/8”
Type 8-5/8”
Pipe Braces *
Plywood Forming *
Coil Ties
Pencil Rod and Clamps
Self-Centering Ties
Snap Ties
Precast
Anchor Rail HD
Coil Inserts *
Column Wall Edge Connector *
Ferrule Inserts *
Helical Ground Anchors *
Ring and Cable Lifters
Slant Anchor *
Straight Leg Anchor *
Wall Base Connector *
Wire / FRP Truss *
* Products are Made in the USA or available to be made in the USA
Rebar Safety Caps
Rebar Splicing
Groutec
Unitec
Self-Riser System *
Shoring *
Cross Braces
Frames
Post Shores
Screw Jacks
Snap Ties *
SPAN-X Beams *
Staybox Rebar Splicing *
Steel Stakes *
3/4” Stakes
7/8” Stakes
Stud Rail DSA & DSAR *
Thermal Break
SurePly™ Handset Forming *
Panels and Fillers
Hardware
HD Loop Ties
X-Flat Ties
Birch Plywood
Tilt-Up
Brace Inserts *
Helical Ground Anchors *
Lifting Hardware
ProLift Inserts *
Slant Anchor *
SureLift (SL) Inserts *
Edge Form Brackets
Construction Adhesive *
FRP Truss / Connectors *
XL Lift Inserts *
Walers *
Butt Plate
Double Channel
2525 Armitage Ave
Melrose Park, IL 60160
708-493-9569
www.surebuilt-usa.com
11/24